Perrin and Rowe Faucet Repair: A Step-by-Step Guide

If you own a Perrin and Rowe faucet, you know that it is a high-quality piece of equipment that can last for years. However, even the best faucets can experience problems from time to time. In this article, we will provide you with a step-by-step guide on how to repair your Perrin and Rowe faucet.

Step 1: Turn Off the Water Supply

The first step in repairing your Perrin and Rowe faucet is to turn off the water supply. This can usually be done by turning off the valve under the sink. If you cannot find the valve, you may need to turn off the water supply to your entire home.

Step 2: Remove the Handle

The next step is to remove the handle from your faucet. This can usually be done by unscrewing a set screw or by prying off a decorative cap and then unscrewing the handle. If you are having trouble removing the handle, try using a handle puller.

Step 3: Inspect the Cartridge

Once you have removed the handle, you should inspect the cartridge. This is the part of the faucet that controls the flow of water. If the cartridge is damaged or worn out, it may need to be replaced.

Step 4: Remove the Cartridge

If the cartridge needs to be replaced, you will need to remove it from the faucet. This can usually be done by unscrewing a retaining nut or by pulling it out with pliers. Be sure to take note of how the cartridge is installed so that you can reinstall it correctly.

Step 5: Install the New Cartridge

If you have a new cartridge, you can install it by reversing the steps you took to remove the old one. Be sure to tighten any retaining nuts or screws securely.

Step 6: Check for Leaks

Once you have installed the new cartridge, you should turn the water supply back on and check for leaks. If you notice any leaks, you may need to tighten the cartridge or use plumber’s tape to seal any gaps.

Step 7: Reinstall the Handle

After you have checked for leaks, you can reinstall the handle. Be sure to tighten any set screws securely.

Step 8: Clean the Aerator

If your faucet is still not working properly, you may need to clean the aerator. This is the part of the faucet that mixes air with water to create a smooth stream. To clean the aerator, simply unscrew it from the faucet and rinse it under running water. If there is any buildup, you can use a toothbrush to scrub it away.

Step 9: Reassemble the Faucet

Once you have cleaned the aerator, you can reassemble the faucet. Be sure to tighten any screws or nuts securely.

Step 10: Test the Faucet

After you have reassembled the faucet, you should test it to make sure it is working properly. Turn on the water supply and check for leaks or any other problems.

Step 11: Check the Supply Lines

If your faucet is still not working properly, you may need to check the supply lines. These are the hoses that connect the faucet to the water supply. Check for any kinks or clogs in the hoses, and make sure that they are securely attached to the faucet and the water supply.

Step 12: Replace the Supply Lines

If the supply lines are damaged or worn out, you may need to replace them. This can usually be done by unscrewing the old lines and screwing in the new ones. Be sure to use Teflon tape to seal any connections.

Step 13: Check the Valve

If your faucet is still not working properly, you may need to check the valve. This is the part of the faucet that controls the water flow. Check for any damage or wear, and make sure that it is securely attached to the faucet.

Step 14: Replace the Valve

If the valve is damaged or worn out, you may need to replace it. This can usually be done by unscrewing the old valve and screwing in the new one. Be sure to use Teflon tape to seal any connections.

Step 15: Check the O-Rings

If your faucet is still not working properly, you may need to check the O-rings. These are the rubber rings that seal the different parts of the faucet. Check for any damage or wear, and make sure that they are securely in place.

Step 16: Replace the O-Rings

If the O-rings are damaged or worn out, you may need to replace them. This can usually be done by unscrewing the affected part of the faucet and replacing the O-rings. Be sure to use Teflon tape to seal any connections.

Step 17: Check the Washer

If your faucet is still not working properly, you may need to check the washer. This is the part of the faucet that seals the water flow. Check for any damage or wear, and make sure that it is securely in place.

Step 18: Replace the Washer

If the washer is damaged or worn out, you may need to replace it. This can usually be done by unscrewing the affected part of the faucet and replacing the washer. Be sure to use Teflon tape to seal any connections.

Step 19: Call a Professional

If you have tried all of these steps and your faucet is still not working properly, you may need to call a professional plumber. They will be able to diagnose the problem and repair your faucet quickly and efficiently.

Step 20: Maintain Your Faucet

To prevent future problems with your Perrin and Rowe faucet, it is important to maintain it properly. This includes cleaning the aerator regularly, checking the supply lines and valves for damage, and replacing any worn or damaged parts as soon as possible.